Important information of the prospective EN 16510

/in /by

We would like to give you again the current information about the restructuring of series of standards of fireplaces by CENT/TC 295 to a new series of standards EN 16510 ” Residential solid fuel burning appliances”.

 

What is EN16510?

The EN 16510 part 1 together with part 2 will supersede EN 13240 for roomheater, EN 13229 for inset appliances, EN 12815 for cookers and EN 12809 for independent boilers. Besides there is also intended that the EN 16510 as well replace the EN 14785 for space heating appliances as well as the EN 15250 for slow heat release appliances.

The parts 1 as well as 2-1 until 2-4 and 2-6 of standard EN 16510 have to agree formally on European level right now.

The WG 7 is working on a preliminary version of part 2-5.

The WG 6 discussed the received comments of part 2-6. The preliminary version of FprEN 16510 Teil 2-6 has been bring to CMC for the formal agreement in May 2016. Furthermore the WG 6 are concerned with the new NWI (New Work Item) for pellet and beech log combo appliances.

The revision of these European Standards takes into account the comments received at their 5-year review. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports fundamental requirements of EU Directives.

The structure of EN 16510, Residential solid fuel burning appliances, is as follows:

— Part 1: General requirements and test methods

— Part 2-1: Roomheaters

— Part 2-2: Inset appliances including open fires

— Part 2-3: Cookers

— Part 2-4: Independent boilers — Nominal heat output up to 50 kW

— Part 2-5: Slow heat release appliances

— Part 2-6: Appliances fired by wood pellets

 

How is the current status of standardization?

At the moment the parts 1, 2-1, 2-2, 2-3, 2-4 and 2-6 are present as preliminary FprEN (final draft).

With release of part 1 of the standard as harmonized standard in Official Journal of the European Union the measurement methods of EN 16510 can be used. This will take place expectedly in March 2017. This part of standard cannot use for appraisal procedure of confirmation. The release of parts 2-1 till 2-4 and 2-6 as harmonized standard in Official Journal of the European Union is displaced for an indefinite period of time because of protest of Norway and Finland. Already now we prepare us and our testing laboratories for the official release.

 

Which consequences does the change of standards have?

The new series of standards differs in their parts in essential points of the former standards, so in many cases additional tests right up to new type tests are required. Anyway a review of the existing test report is necessary if this one and the underlay test also fulfill the requirements of EN 16510. Is this the case we expectedly can write a new test report according to EN 16510. Because there are also new requirements set on the test report.

We are strived our tests continually adapt to the requirements of the preliminary EN 16510. So current tests fulfill the requirements and can be rewritten. Also type tests during this year before taking effect of the series of standards expectedly can rewritten (to this date valid stand of standards will be considered).

 

What is the timing?

Like already mentioned above with release of part 1 of the standard as harmonized standard in Official Journal of the European Union the measurement methods of EN 16510 can be used. This will take place expectedly in March 2017. This part of standard cannot use for appraisal procedure of confirmation. The release of parts 2-1 till 2-4 and 2-6 as harmonized standard in Official Journal of the European Union is displaced for an indefinite period of time because of protest of Norway and Finland. Already now we prepare us and our testing laboratories for the official release.

For the series of standard EN 16510 the competent committee CEN/TC 295 has to apply the interim period of three years at the European Commission. Until the end of coexistence period it is possible to place on the market according to the existing hENs (for example EN 13240). After expiration of the coexistence period the fireplaces need a valid type test according to hEN 16510.

 

Is your test report ready for EN 16510?

Important information of the prospective EN 16510

/in /by

Is your test report ready for EN 16510?

We would like to give you again the current information about the prospective series of standards EN 16510.

 

What is EN16510?

The EN 16510 part 1 together with part 2 will supersede EN 13240 for roomheater, EN 13229 for inset appliances, EN 12815 for cookers and EN 12809 for independent boilers. Besides there is also intended that the EN 16510 as well replace the EN 14785 for space heating appliances as well as the EN 15250 for slow heat release appliances.

The revision of these European Standards takes into account the comments received at their 5-year review. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association.

The structure of EN 16510, Residential solid fuel burning appliances, is as follows:

— Part 1: General requirements and test methods

— Part 2-1: Roomheaters

— Part 2-2: Inset appliances including open fires

— Part 2-3: Cookers

— Part 2-4: Independent boilers — Nominal heat output up to 50 kW

— Part 2-5: Slow heat release appliances

— Part 2-6: Appliances fired by wood pellets

 

How is the current status of standardization?

At the moment the parts 1, 2-1, 2-2, 2-3 and 2-4 are present as preliminary FprEN (final draft).

We cannot tell you the date of commencement by now because there are no official news. To prepare us and our testing laboratories we assume that the commencement will be start in spring 2017.

 

Which consequences does the change of standards have?

The new series of standards differs in their parts in essential points of the former standards, so in many cases additional tests right up to new type tests are required. Anyway a review of the existing test report is necessary if this one and the underlay test also fulfill the requirements of EN 16510. Is this the case we can write a new test report according to EN 16510. Because there are also new requirements set on the test report.

We are strived our tests continually adapt to the requirements of the preliminary EN 16510. So current tests fulfill the requirements and can be rewritten. Also type tests during this year 2016 are valid by the to this date valid stand of standards.

 

What is the timing?

Like already mentioned above there isn´t a concrete date of commencement. We prepare internally for a commencement starting in spring 2017. After the commencement their will be a interim period (3 years are requested / expected interim period is 2 years). If the interim period is over the declaration of performance of a building product has to be imperative base on a valid test report recording to EN 16510.

Because the review of a test report or a necessary additional test and the corresponding new test report according to EN 16510 is very time consuming, the interim period is relatively short, so you should care about the reorganization early.

We would like to inform you by phone or be available for you for a one-to-one conversation.

From 24th to 26th of February 2016 we are on the fair Progetto Fuoco in Verona. We also would like to offer a one-to-one conversation if you wish that.

New Danish regulation for fireplaces entered into force on 22.01.2015

/in /by

On 22.01.2015 the new Danish regulation for fireplaces “regulering af luftforurening fra fyringsanlæg til fast brændsel under 1 MW” entered into force. It contains new limit values for fireplaces with and without boiler, which will be valid from 26.07.2015:

 

Dust/particles:

5 g/kg (10 g/kg) according to NS 3058-1 and NS 3058-2 (Norwegian method)

or  40 mg/m³ according to DINplus method

OGC:                150 mg/m³

 

2 years after entry into force the limit values for above mentioned fireplaces will be tightened:

Dust/particles:

4 g/kg (8 g/kg) according to NS 3058-1 and NS 3058-2 (Norwegian method)

or  30 mg/m³ according to DINplus method

OGC:                120 mg/m³

 

 

Link: https://www.retsinformation.dk/forms/r0710.aspx?id=167776#Kap9  (Bilag 1)

 

Grænseværdier / emissionskrav for rumopvarmere

Rumopvarmere med og uden vandtank skal opfylde grænseværdierne for støv og OGC, dog kun ved en af prøvningsmetoderne for støv:

Stof Grænseværdi Måleprincip Prøvningsmetode
Støv 5 g/kg, og en maksimal emission på 10 g/kg i de enkelte prøvningsintervaller Fortyndingstunnel NS 3058-1 og NS 3058-2 (udregnet efter NS 3059, klasse 1 eller 2, afhængig af fyringsanlæggets størrelse) eller en tilsvarende standard for måling af partikelemission fra rumopvarmere, anerkendt i EU, EFTA-lande eller Tyrkiet.
40 mg/normal m3 ved 13 % O2 Direkte i røggaskanalen Relevant harmoniseret produktstandard, eller hvis ikke denne indeholder beskrivelse af emissionsmålemetoder, så CEN/TS15883, Annex A. 1 (Apparater til fast brændsel til husholdningsbrug – Metoder til emissionsprøvning), eller tilsvarende standard for måling af partikelemissioner fra rumopvarmere, anerkendt i EU, EFTA-lande eller Tyrkiet.
OGC 150 mg C/normal m3 ved 13 % O2 Direkte i røggaskanalen Relevant harmoniseret produktstandard, eller hvis ikke denne indeholder beskrivelse af emissionsmålemetoder, så CEN/TS15883, Kapitel 4 (Apparater til fast brændsel til husholdningsbrug – Metoder til emissionsprøvning), eller tilsvarende standard for måling af OGC emission fra rumopvarmere, anerkendt i EU, EFTA-lande eller Tyrkiet.

Fra d. (= 2 år efter ikrafttrædelsesdatoen) skal rumopvarmere med og uden vandtank opfylde emissionskravene for støv og OGC, dog kun ved en af prøvningsmetoder for støv:

Stof Grænseværdi Måleprincip Prøvningsmetode
Støv 4 g/kg, og en maksimal emission på 8 g/kg i de enkelte prøvningsintervaller Fortyndingstunnel NS 3058-1 og NS 3058-2 (udregnet efter NS 3059, klasse 1 eller 2, afhængig af fyringsanlæggets størrelse) eller en tilsvarende standard for måling af partikelemission fra rumopvarmere, anerkendt i EU, EFTA-lande eller Tyrkiet.
30 mg/normal m3 ved 13 % O2 Direkte i røggaskanalen Relevant harmoniseret produktstandard, eller hvis ikke denne indeholder beskrivelse af emissionsmålemetoder, så CEN/TS15883, Annex A. 1 (Apparater til fast brændsel til husholdningsbrug – Metoder til emissionsprøvning), eller tilsvarende standard for måling af partikelemissioner fra rumopvarmere, anerkendt i EU, EFTA-lande eller Tyrkiet.
OGC 120 mg C/normal m3 ved 13 % O2 Direkte i røggaskanalen Relevant harmoniseret produktstandard, eller hvis ikke denne indeholder beskrivelse af emissionsmålemetoder, så CEN/TS15883, Kapitel 4 (Apparater til fast brændsel til husholdningsbrug – Metoder til emissionsprøvning), eller tilsvarende standard for måling af OGC emission fra rumopvarmere, anerkendt i EU, EFTA-lande eller Tyrkiet.
Grundofen

Change the limit values by new Art. 15a B-VG for Austria and important information for tiled stove/heat storage fireplace manufacturer (2015)

/in /by

As of 01.01.2015 new laws in Austria apply

On 31.12.2012 the Official Gazette for Vienna published the new

agreement in accordance with Article 15a B-VG on the marketing of residential heating and review of combustion plants and cogeneration units.

The limit values in the product range of solid fuel-fired appliances have changed. These chances or tightening of the values are valid from 01.01.2015.

From this date every fireplace which is going to place on the market has to fulfill this limit values:

Excerpt from the Article 15a B-VG:

Manually-fed roomheaters *) (wood fuels):
CO emissions = 1100 mg/MJ (unchanged)
NOx = 150 mg/MJ (unchanged)
OGC emissions = 50 mg/MJ (previously 80 mg/MJ)
Dust emissions = 35 mg/MJ (previously 60 mg/MJ)
Minimum efficiency = 80% (previously 78%)

Automatically-fed roomheaters **) (wood pellets):
CO emissions = 500 mg/MJ (unchanged)
NOx = 100 mg/MJ (previously 150 mg/MJ)
OGC emissions = 30 mg/MJ (unchanged)
Dust emissions = 25 mg/MJ (previously 50 mg/MJ)
Minimum efficiency = 80% (previously 78%)

*) for example roomheaters according to: DIN EN 13240, DIN EN 13229, DIN EN 12815, DIN EN 15250, DIN EN 15821

**) for example roomheaters according to: DIN EN 14785

Compliance with the limit values shall be verified by the appropriate type tests.

 

As of 01.01.2015 heat storage fireplaces have to prevent a confirmation of emissions

With come into effect of the first regulation implementing the Bundes-Immissionsschutzgesetz (BImSchV) of 22.03.2010 heat storage fireplaces have to prevent a confirmation of emission’s as of 01.01.2015.
This confirmation can be fulfilled with two methods:

  1. Local measuring after installation of the appliance
  2. Type test of the fireplace or of a fireplace family according to an acknowledged standard through an accredited body (like RRF)

The limit values of heat storage inset appliances with fill-in firing in accordance with DIN EN 13229/A1 are valid.

If you as a manufacturer of heat storage fireplaces or tiled stoves have the request of detailed information, it would be a pleasure for us to inform you by phone or in a personal conversation.

Flagge Europas

Construction products regulation (EU) No. 305/2011

/in /by

This regulation lays down conditions for the marketing of construction products or preparation on the market as of the 1 July of 2013 through the placement of harmonized regulations by the information of the efficiency of construction products in reference to the essential characteristics as well as by use of the CE-label for these products. In Germany the regulation was assimilated in the building products act and so its legally binding.

What will change for the manufacturer of solid fuel fireplaces?
Up to now it was enough to certificate a declaration of conformance and to attach a CE-label on the construction product. The declaration of conformance is extended and is going to call declaration of performance in the future. The CE-label also changes and has to feature a correlation to the corresponding declaration of performance.

What will change for already marketed construction products?
Construction products, which where on the market in accordance with the regulation 89/106/EWG before 1 July of 2013 deemed compliant with this regulation. The manufacturer can create a declaration of performance based on a certificate of conformance or a declaration of conformance. A change of the CE-label is not necessary.

What will change for notified bodies?
Basic for notification of a body through the European Commission is an accreditation in accordance with ISO/IEC 17025. The accreditation has to verify a body for the permission of test operations after the 1 July 2013.
RRF accreditation: DIN EN ISO/IEC 17025:2005, DAkkS No. D-PL-17727-01-00